{"product_id":"garmin-ondeck-relay-switch-24-v-dc","title":"Garmin OnDeck relay switch (24 V DC)","description":"\u003cp\u003eControl the boat remotely using the OnDeck™ hub and the relay switch. Add up to five switches to the OnDeck hub to stay in control. Check that the input power of the OnDeck hub works between 15.6 and 31.2 V DC to ensure compatibility with your system.\u003c\/p\u003e\u003c!-- sr-faq v=1 vendor=garmin source_sha256=6a9c7d9707ba4d2b21a6c2e00a35f06d1a293d82faa7be95b02d5ca7c02889c1 --\u003e\u003ch3\u003eFAQs\u003c\/h3\u003e\u003cdetails\u003e\u003csummary\u003eIs a fuse required for the relay switch installation?\u003c\/summary\u003e\u003cdiv\u003e\u003cp\u003eA 1 Amp fuse should be installed on all relay controls at the positive input to the power source. The relay’s positive control (black) wire must connect through this fuse.\u003c\/p\u003e\u003c\/div\u003e\u003c\/details\u003e\u003cdetails\u003e\u003csummary\u003eWhat are the wiring requirements for installing the OnDeck relay switch?\u003c\/summary\u003e\u003cdiv\u003e\u003cp\u003eAll connections must use proper electrical connectors, and bare wire connections exposed to moisture should be watertight. Use heat-shrink type butt connectors or other water-tight connections. If wire extension is needed, use a minimum of 24 AWG (0.08 mm²) wire.\u003c\/p\u003e\u003c\/div\u003e\u003c\/details\u003e\u003cdetails\u003e\u003csummary\u003eAre there special safety procedures when installing the relay switch?\u003c\/summary\u003e\u003cdiv\u003e\u003cp\u003eAlways disconnect the vessel's power supply before installation. Wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding.\u003c\/p\u003e\u003c\/div\u003e\u003c\/details\u003e\u003cdetails\u003e\u003csummary\u003eIs any setup required after installing the relay switch?\u003c\/summary\u003e\u003cdiv\u003e\u003cp\u003eRelay switches must be set up in the ActiveCaptain app after installation for remote control.\u003c\/p\u003e\u003c\/div\u003e\u003c\/details\u003e\u003cdetails\u003e\u003csummary\u003eAre there any environmental mounting restrictions?\u003c\/summary\u003e\u003cdiv\u003e\u003cp\u003eInstall the relay switch and connected devices in a dry area. Do not expose to water or mount where flooding may occur.\u003c\/p\u003e\u003c\/div\u003e\u003c\/details\u003e\u003cdetails\u003e\u003csummary\u003eCan the relay switch be submerged or installed below the waterline?\u003c\/summary\u003e\u003cdiv\u003e\u003cp\u003eYou must mount the device where it will not be submerged. For optimal performance, mount above the waterline and in a dry, ventilated area.\u003c\/p\u003e\u003c\/div\u003e\u003c\/details\u003e\u003cdetails\u003e\u003csummary\u003eHow should the relay switch be connected to power?\u003c\/summary\u003e\u003cdiv\u003e\u003cp\u003eThe relay's positive control (black) wire connects through a 1 Amp fuse to the positive side of the same power source as the GTB 10 device. Make sure relay and black box share the same positive source.\u003c\/p\u003e\u003c\/div\u003e\u003c\/details\u003e\u003cdetails\u003e\u003csummary\u003eIs this relay switch intended for direct connection to high-current loads?\u003c\/summary\u003e\u003cdiv\u003e\u003cp\u003eEach relay control wire is rated for up to 1 A. For higher-current loads, external relay switches are required. Do not connect these wires to the positive side of a power source.\u003c\/p\u003e\u003c\/div\u003e\u003c\/details\u003e\u003cdetails\u003e\u003csummary\u003eShould relay switches be installed near sources of interference?\u003c\/summary\u003e\u003cdiv\u003e\u003cp\u003eMount at least 102 mm (4 in.) from cables and other potential sources of interference for optimal performance.\u003c\/p\u003e\u003c\/div\u003e\u003c\/details\u003e\u003cdetails\u003e\u003csummary\u003eWhat are the mounting location requirements for the OnDeck relay switch?\u003c\/summary\u003e\u003cdiv\u003e\u003cp\u003eMount the relay switch in a location that is dry and not exposed to extreme temperatures, with adequate ventilation, and at least 102 mm (4 in.) from cables and interference sources.\u003c\/p\u003e\u003c\/div\u003e\u003c\/details\u003e\u003cdetails\u003e\u003csummary\u003eHow should I connect the load (device being switched) to the relay?\u003c\/summary\u003e\u003cdiv\u003e\u003cp\u003eConnect the positive wire from the item's power cable to the relay’s negative load (blue) wire, and connect the relay’s positive load (yellow) wire to the positive terminal of the item’s power source.\u003c\/p\u003e\u003c\/div\u003e\u003c\/details\u003e\u003cscript type=\"application\/ld+json\"\u003e{\"@context\": \"https:\/\/schema.org\", \"@type\": \"FAQPage\", \"mainEntity\": [{\"@type\": \"Question\", \"name\": \"Is a fuse required for the relay switch installation?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"A 1 Amp fuse should be installed on all relay controls at the positive input to the power source. The relay’s positive control (black) wire must connect through this fuse.\"}}, {\"@type\": \"Question\", \"name\": \"What are the wiring requirements for installing the OnDeck relay switch?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"All connections must use proper electrical connectors, and bare wire connections exposed to moisture should be watertight. Use heat-shrink type butt connectors or other water-tight connections. If wire extension is needed, use a minimum of 24 AWG (0.08 mm²) wire.\"}}, {\"@type\": \"Question\", \"name\": \"Are there special safety procedures when installing the relay switch?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Always disconnect the vessel's power supply before installation. Wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding.\"}}, {\"@type\": \"Question\", \"name\": \"Is any setup required after installing the relay switch?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Relay switches must be set up in the ActiveCaptain app after installation for remote control.\"}}, {\"@type\": \"Question\", \"name\": \"Are there any environmental mounting restrictions?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Install the relay switch and connected devices in a dry area. Do not expose to water or mount where flooding may occur.\"}}, {\"@type\": \"Question\", \"name\": \"Can the relay switch be submerged or installed below the waterline?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"You must mount the device where it will not be submerged. For optimal performance, mount above the waterline and in a dry, ventilated area.\"}}, {\"@type\": \"Question\", \"name\": \"How should the relay switch be connected to power?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"The relay's positive control (black) wire connects through a 1 Amp fuse to the positive side of the same power source as the GTB 10 device. Make sure relay and black box share the same positive source.\"}}, {\"@type\": \"Question\", \"name\": \"Is this relay switch intended for direct connection to high-current loads?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Each relay control wire is rated for up to 1 A. For higher-current loads, external relay switches are required. Do not connect these wires to the positive side of a power source.\"}}, {\"@type\": \"Question\", \"name\": \"Should relay switches be installed near sources of interference?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Mount at least 102 mm (4 in.) from cables and other potential sources of interference for optimal performance.\"}}, {\"@type\": \"Question\", \"name\": \"What are the mounting location requirements for the OnDeck relay switch?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Mount the relay switch in a location that is dry and not exposed to extreme temperatures, with adequate ventilation, and at least 102 mm (4 in.) from cables and interference sources.\"}}, {\"@type\": \"Question\", \"name\": \"How should I connect the load (device being switched) to the relay?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Connect the positive wire from the item's power cable to the relay’s negative load (blue) wire, and connect the relay’s positive load (yellow) wire to the positive terminal of the item’s power source.\"}}]}\u003c\/script\u003e\u003c!-- \/sr-faq --\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":51626145382737,"sku":"010-13009-07","price":40.45,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0955\/4434\/4913\/files\/garmin-ondeck-relay-switch-12-v-dc-ondecktm-relay-switch-12-v-dc_b35758d9-39cc-48c9-92a8-a3b0f7ee97ec.webp?v=1754729622","url":"https:\/\/www.sailrace.com\/ru-caucasus\/products\/garmin-ondeck-relay-switch-24-v-dc","provider":"SailRACE","version":"1.0","type":"link"}